How to charge a car battery?
Many have a type for Industries, such as: Electronics, Featured, Science, Technology, Tips and trick for the comment and advice about electronict for the future , and then HOW TO FILLING ACCU about the best electronic and luxury, after that many have a battery, I will give to your information of Batteries often encountered in the automobile, motorcycle, or mobile phone. One of the main cases that I have encountered is the problem of charging the battery or the term Charge. The problems I encountered in the workplace is a problem for AGV charge batteries that should be quick in charging batteries. Charge the batteries (car batteries) is the flow of electrical energy from the outside into a solution of the battery, causing a reaction in the electrolyte and battery cells.
No Battery Charging Method.
1. Charging Normal
Do you know of normal charging, the charging with a large current is normal, normal large charging current of 10% of the battery capacity. Example: 50 AH battery charging current, the large 50 x 10/100 = 5 A. So if we have a battery (batteries) with a capacity of 50Ah then when charging takes current from charging tool for 5A. O> Old Time charging
When charging is definitely the gi want is accu in full condition. for determine how long to charging The time have used and the following formula, Charging time (hours) = (Large capacity battery [AH] / Large charge current [AH]) + 20%
* 20% of the division of the capacity of the battery / charger current
If we do have the capacity 42AH batteries, the charging current is 4.2a, the time required is 11 hours
or if not complicated charging time can use the calculator below accu about the best electronic and luxury
2. Fast Charging
Fast charging with very large currents. Large charging must not exceed 50% of the battery capacity, thus for 50 AH battery, large charging current may not exceed 25 Ampere. Fast charging procedure is virtually identical to the normal charging, the different large charging current is regulated very large. There was also the risk of a much larger, so it must be done with extra caution. Be carefully and you can read the books for the follow to instructions,
Also Read: Google Chromebit Chrome OS packs an entire computer into an HDMI stick, Fast charging is often carried out to help the vehicles broke down or are in the process of repair, so that the battery is not derived from a vehicle. In the case of quick charging on the vehicle to keep in mind is off the negative battery cable before charging, this is due to the current rapid charging of the battery charging voltage is greater than the normal charging, this condition is potentially damaging electronic components and diodes in the alternator about the best electronic and luxury.
Battery Charging Techniques.
1. Charging the battery
Connect the battery positive cable to the positive clamp battery charger and the negative terminal clamp acknowledgment is negative and the best electronic and luxury. Be careful not to reverse, if reverse sparks will arise, when the battery is forced to be broken, the battery charger is equipped with indicator of certain models, which will appear upside down when the installation warning message.
Replacing the battery charger
2. Charging more than one battery
Charging the battery is more than one can be done by two methods, namely:
a. Parallel circuit 2 batteries
Connect the battery positive cable first to the positive battery terminal 2 then connect the battery charger positive clamp. Similarly to the negative terminal.
Be careful not to reverse, if reverse sparks will arise, when the battery is forced to be broken, the battery charger is equipped with indicator of certain models, which will appear upside down when the installation warning message.
Charging two batteries in parallel
o> Select the voltage selector according to the battery voltage, eg 12 V battery, the selector is tilted 12V.
o> Turn on the battery charger, and a large set according to the current battery capacity.
o> Large flow is the amount of current required for battery 1 and battery 2. example to fill two 50 AH battery needed charging current of 10% x (2 x 50)) = 10 A., charging 50 AH and 40 AH, the required flow 10% x (40 + 50) = 9A.
b. Series 2 battery circuit
Also Read: Difference between Front End, Back End and Full Stack Developer, Connect the battery positive cable clamp 1 to the positive battery charger, then connect the negative cable to the battery 1 2 battery positive cable, then connect the negative battery cable clamp 2 with the negative battery charger. Be careful not to reverse, if reverse sparks will arise, when the battery is forced to be broken, the battery charger is equipped with indicator of certain models, which will appear upside down when the installation warning message.
ACCU charging in series
Note: Connect battery charger with 220V power source.
Select the voltage selector according to the total battery voltage, eg 12 V battery assembled two series then the voltage to 24 V, the selector is tilted 24 V.